![how to install wd my book external hard drive how to install wd my book external hard drive](https://www.lifewire.com/thmb/xmmo-z8hTo6MoC5XjCk7Li5XsR8=/1500x1124/filters:no_upscale():max_bytes(150000):strip_icc()/3LW4050413_3-75dc8db4620247c99c209b5324df127e.jpg)
- #How to install wd my book external hard drive upgrade
- #How to install wd my book external hard drive full
- #How to install wd my book external hard drive software
- #How to install wd my book external hard drive windows
#How to install wd my book external hard drive upgrade
I'm dealing with it, but it does appear that the firmware upgrade did the trick on the rest of them if I leave the BIOS at v.
#How to install wd my book external hard drive windows
Don't know if it's coincidence or an incompatibility, but after upgrading the firmware on all the Western Digital external drivesĪnd running daily backups, installing windows updates and scheduling reboots overnight to install updates, the ONLY server (out of 6 with this setup) that is not detecting the drive on reboot is the server that has the updated BIOS and new hardware. During that process, Dell upgraded the BIOS on that machine from what is on all the rest of them. Thank God it was there and restorable! We had a RAID 1 array set up in this server that was supposed to avert this being needed, but we were not successful in geting theĪrray back. Had to restore from one of the backups on one of these external hard drives. After much troubleshooting, Dell Support replaced the system board and one hard drive under warranty and I amid the firmware upgrades, one of my Dell T110 II servers crashed and would not boot. I'll report back how it goes and if anyone else has input, please share. If this doesn't work, anybody know if it's an issue with the drive 'going to sleep' if I could somehow set up a task that would write and erase data to the drive every so often to keep it awake? I've done that in the past, however, since Windows Serverīackup takes total control of the drive I have as a dedicated device and it isn't given a drive letter, I'm guessing that may not be possible. I'll monitor them as well as continue to try to get the rest of them updated to the latest firmware. Time will tell if they now stay connected.
![how to install wd my book external hard drive how to install wd my book external hard drive](https://www.rigassembler.com/media/2019/05/39_6c573cdb-e238-4983-b297-d8c7dbfe6693.jpg)
Luckily, weĪre small and I could tell everyone at the locations that I had to reboot and it went well. The only downside was that it said I needed to reboot the servers after the f/w upgrade. I'm really hoping this is a fix for the problem. Both were viewable in Disk Management and successfully ran a backup. 3.2.0.8) following the instructions given by WD to a tee.
#How to install wd my book external hard drive software
This afternoon I went to 2 of the locations and ran the WDFirmwareUpdater software (v. Has anybody seen this issue and know what the fix is? This is driving me nuts. We are a non-profit and cannot afford to replace all of these drives so I hope I can get them working and that the backups are restorable. WD tells me those drives might work, but that Windows Server 2012 is My next step is to go to the locations and try to run firmware updates on the drives, but I haven't found any documentation as to whether this is really a fix for what is happening. I've remoted to each server and made sure the USB hubs in device manager have the box unchecked that allows the OS to turn off the device to save power as I thought that might be the problem. This has happened to all of them but not at the same I then drive across town to the location and have to disconnect power & usb to the drive, wait a little bit, then reconnect and it will come up and be recognized again and work for a few days. "Windows Backup cannot find any of the backup storage locations" and the drive does not show in Disk Management. All was OK, then one randomly failed & continued to fail because the drive was unavailable. Main office each morning after backups ran to be certain that they backups completed (which they did initially). I started remotely connecting to these machines from the
#How to install wd my book external hard drive full
Also included is the advanced VSS Full Backup option. The backup jobs are identical on each machine. We have the data being backed up on our network using another solution as well. We have set up Windows Server Backup to do a dailyīackup to these drives which initially works on all of them. We also purchased several Western Digital 3TB My Book Essentials external hard drives with one connected to each server via usb (these are usb 3.0 capable, but the servers don't have 3.0 ports). Each is at a different physical location, but sites are connected via VPN to our network. Our agency recently installed six new Dell PowerEdge T110 II servers running Windows Server 2012 Standard.